Bently Nevada 330171-00-12-10-02-00 3300 XL 5 mm Proximity Probe

Product Description

Configured for shaft displacement measurement in Bently Nevada machinery monitoring systems, the Bently Nevada 330171-00-12-10-02-00 (330171 3300 XL 5 mm Proximity Probe) provides direct non-contact eddy-current sensing. The probe converts changes in the probe-to-target gap into an electrical signal for vibration and position monitoring. Its TipLoc molded construction strengthens the bond between the probe tip and body, while the CableLoc design provides increased cable retention strength.

Hardware Specifications

Eddy-Current Probe Scaling and Gap Validation

The Bently Nevada 330171-00-12-10-02-00 operates as part of an eddy-current proximity measurement chain. The probe responds to changes in the electromagnetic field produced near a conductive target surface. Consequently, probe installation requires correct mechanical positioning and compatible system scaling.

The resulting signal supports shaft displacement and vibration monitoring when used with the applicable extension cable and Proximitor sensor components. Gap voltage validation may also be used during installation to confirm the operating position of the probe relative to the target. A nominal -10 VDC target is commonly associated with Bently Nevada proximity measurement system setup, subject to the applicable system configuration and target material.

The 3300 XL design also addresses mechanical cable retention. The patented TipLoc molding method reinforces the probe tip-to-body connection. In addition, the CableLoc construction provides 330 N (75 lbf) pull strength to improve the mechanical attachment between the probe cable and probe tip.

Frequently Asked Questions

Q: What does the 330171-00-12-10-02-00 measure?
A: The probe detects changes in the distance between the 5 mm probe tip and a conductive target. The measurement chain can use this signal for shaft displacement, position, and vibration monitoring.

Q: What mounting thread does the probe use?
A: The probe uses a 1/4-28 UNF thread. The mounting arrangement must maintain correct probe alignment and sufficient mechanical clearance around the probe tip.

Q: Can the probe cable be pulled during installation?
A: The CableLoc design provides 330 N (75 lbf) pull strength. However, installation should avoid unnecessary cable tension, sharp bends, crushing, or mechanical loading at the connector and probe transition points.

Field Installation Guidelines

Install the Bently Nevada 330171-00-12-10-02-00 in a correctly threaded mounting location using the 1/4-28 UNF probe thread. Align the probe tip with the conductive target surface and prevent mechanical contact during machine operation.

Route the probe cable separately from high-current power conductors where practical. Avoid sharp bends, cable crushing, and excessive tensile loading. Maintain the connector and cable interfaces in accordance with the applicable Bently Nevada proximity measurement system installation requirements.

Verify the complete probe, extension cable, and Proximitor sensor combination before commissioning. In addition, perform gap validation according to the applicable machinery monitoring system procedure and confirm that the target material and surface condition are compatible with the configured measurement system.

Other Attribute

• Series: 3300 System
• Country of Origin: USA
• Lead Time: In Stock, 2 Working Days

In Stock Hot Items of The 3500 System

Our Competitive Brands

• - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT
• - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax
• - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,
• - Bently Nevada 3300 System, 3500 System
• - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)
• - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC
• - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider

 TEL: +86 18030205725 E-MAIL: manskiwong@cambia.cn

Question 1: Is Our Price Competitive?

NEW-GEN collaborates with over 50 countries worldwide. As a leading supplier in China, we can provide significant discounts to customers based on market demand.

Question 2: What Is The Warranty Period?

We offer a standard one-year warranty for all new and original items.

Question 3: What Payment Methods Do We Accept?

We accept 100% T/T (Telegraphic Transfer) before shipping. For items with a lead time, a 30% deposit is required in advance, with the remaining 70% balance due before shipping. If you have an agent in China, please contact us for RMB transfer.

Question 4: What Shipping Methods Do We Use?

We primarily utilize carriers such as FedEx, DHL, UPS, BRE, etc. If you have an account with any of these carriers, you can arrange the shipping yourself. Additionally, we offer free shipping to China freight forwarders.

Question 5: What Is Our Delivery Time?

Typically, delivery takes around 1-3 days after receiving the advance payment. For items with a quoted lead time, delivery will occur as per the specified lead time.

Question 6: How Do We Package The Goods?

Our packaging process involves multiple layers of protection. Initially, the product is placed in its original box, sealed with a label. Then, we add a layer of bubble wrap to safeguard against collisions during transportation. Finally, all products are securely packed in sturdy boxes for further protection.

Question 7: How Can Customers Contact Us And Request A Quote?

Customers can inquire via email, WhatsApp, WeChat, Skype, or any preferred communication platform. Simply reach out to us, and we'll promptly provide a quote tailored to your needs.