MU-TSIM12 Honeywell Serial Interface I/O Processor FTA

Product Description

The Honeywell MU-TSIM12, identified by the base model MU-TSIM12, is a Serial Interface I/O Processor / Field Termination Assembly (FTA) for Modbus RTU communication within Honeywell process control systems. It connects compatible third-party devices through EIA-232 or EIA-485 serial interfaces and transfers Boolean, numeric, integer, and ASCII string data to the control system. The interface supports asynchronous bidirectional communication, with half-duplex operation in EIA-485 mode.

Hardware Specifications

Modbus RTU Communication and Data Handling

The MU-TSIM12 uses serial Modbus RTU framing to exchange data with compatible external devices. The selected physical interface determines the electrical wiring and network topology.

• EIA-232: Supports transmit, receive, handshake, signal ground, and protective ground lines. The maximum device connection distance is 15 m, subject to the specified cable capacitance limit.
• EIA-485: Supports a two-wire differential pair using Data+ (B) and Data- (A), with protective ground for the cable shield. The interface operates in half-duplex mode and supports up to 15 drops over a maximum specified distance of 1.2 km.
• Data mapping: Each serial channel handles 16 points organized as arrays in the APMM/HPMM. Depending on the configured point type, the supported data allocation includes Boolean flags, real values, signed integers, diagnostic counters, and ASCII strings.
• Protocol configuration: Baud rate, parity, modem control, keep-alive cell writes, and response timeout settings can be configured according to the device interface requirements.
• Exception handling: The interface reports Modbus exception errors. Supported function codes include read operations, single-coil and single-register writes, diagnostics, and multiple-register writes.

Serial Interface Electrical Characteristics

The EIA-485 interface uses differential signaling for multidrop communication. Its stated common-mode operating capability is 250 VAC RMS continuous. This specification should not be interpreted as permission to apply that voltage to the signal terminals or as a substitute for the manufacturer's wiring and grounding requirements.

The EIA-232 interface provides separate transmit and receive signals and additional modem-control lines. Select the physical interface according to the connected device's electrical interface, wiring distance, and communication configuration.

The supplied specifications do not establish optical isolation, channel-to-channel isolation, or a specific power consumption value. These characteristics require confirmation from the applicable Honeywell hardware documentation.

Frequently Asked Questions (FAQ)

Q: Which serial protocols and physical interfaces does the MU-TSIM12 support?

A: It supports Modbus RTU over EIA-232 or EIA-485. EIA-485 operates in two-wire, half-duplex mode. The supported baud rates range from 1200 to 19200 bps.

Q: How many external devices can connect to the interface?

A: The specifications allow up to 15 devices per FTA and two FTAs per Serial Interface I/O Processor. For EIA-485, the stated maximum device distance is 1.2 km. Actual network performance depends on cable characteristics, topology, grounding, and device configuration.

Q: Which Modbus function codes are supported?

A: The listed function codes are 01, 02, 03, 04, 05, 06, 08, and 16. Confirm the required operation and register mapping against the configuration of each connected Modbus device.

Field Installation Guidelines

1. Verify the MU-TSIM12 model and applicable FTA hardware documentation before installation.
2. Select EIA-232 or EIA-485 to match the connected device. Confirm baud rate, parity, stop bits, device address, and data format at both ends.
3. For EIA-232, keep the cable within the specified 15 m distance and 2500 pF capacitance limit.
4. For EIA-485, connect the differential pair with consistent polarity. Observe the manufacturer's requirements for termination, biasing, cable topology, and maximum network length.
5. Route communication cables away from high-voltage conductors, motor cables, and other sources of electrical interference.
6. Connect cable shields and protective grounds according to the system grounding design. Avoid creating unintended ground loops.
7. Configure response timeouts and keep-alive behavior to match the connected devices and communication requirements.
8. Verify data mapping, register addresses, exception reporting, and communication status before placing the interface into operational service.

Other Attributes

• Series: Honeywell Experion PKS(C200,C300)
• Country of Origin:  USA
• Lead Time: In Stock, 2 Working Days

In Stock Hot Items of Honeywell

Our Competitive Brands

• - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT
• - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax
• - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,
• - Bently Nevada 3300 System, 3500 System
• - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)
• - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC
• - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider

TEL: +86 18030205725     E-MAIL: manskiwong@cambia.cn

Question 1: Is Our Price Competitive?

NEW-GEN collaborates with over 50 countries worldwide. As a leading supplier in China, we can provide significant discounts to customers based on market demand.

Question 2: What Is The Warranty Period?

We offer a standard one-year warranty for all new and original items.

Question 3: What Payment Methods Do We Accept?

We accept 100% T/T (Telegraphic Transfer) before shipping. For items with a lead time, a 30% deposit is required in advance, with the remaining 70% balance due before shipping. If you have an agent in China, please contact us for RMB transfer.

Question 4: What Shipping Methods Do We Use?

We primarily utilize carriers such as FedEx, DHL, UPS, BRE, etc. If you have an account with any of these carriers, you can arrange the shipping yourself. Additionally, we offer free shipping to China freight forwarders.

Question 5: What Is Our Delivery Time?

Typically, delivery takes around 1-3 days after receiving the advance payment. For items with a quoted lead time, delivery will occur as per the specified lead time.

Question 6: How Do We Package The Goods?

Our packaging process involves multiple layers of protection. Initially, the product is placed in its original box, sealed with a label. Then, we add a layer of bubble wrap to safeguard against collisions during transportation. Finally, all products are securely packed in sturdy boxes for further protection.

Question 7: How Can Customers Contact Us And Request A Quote?

Customers can inquire via email, WhatsApp, WeChat, Skype, or any preferred communication platform. Simply reach out to us, and we'll promptly provide a quote tailored to your needs.