GE IS200TVIBH2B Mark VI Vibration Input Terminal Board

Product Description

The GE IS200TVIBH2B, also identified by the base model IS200TVIBH2B, is a vibration input terminal board designed to interface vibration sensor signals with the GE Mark VI turbine control system. It supports connections for up to 13 probes, subject to the applicable system configuration. The board provides the physical signal interface for vibration monitoring circuits.

Hardware Specifications

Vibration Signal Interface and Measurement

The IS200TVIBH2B provides terminal connections for vibration monitoring signals within the Mark VI control architecture. Its stated probe capacity is up to 13 probes. Actual channel assignments and supported sensor combinations must be confirmed against the applicable terminal board documentation and system configuration.

For proximity probe circuits, verify the sensor output range, cable arrangement, and signal conditioning requirements before connecting the field wiring. The specified 0-10 kHz range applies to the supplied proximity probe data and should not be interpreted as a guaranteed measurement bandwidth for every connected sensor configuration.

Accelerometer signals may extend to 20 kHz according to the supplied specifications. Where IEPE sensors are used, confirm excitation voltage compatibility and input interface requirements. The stated +/-10 V peak analog input range should also be checked against the receiving circuit specifications.

Frequently Asked Questions

Q: How many vibration probes can the IS200TVIBH2B support?

A: The supplied specifications state a capacity of up to 13 probes. Confirm the actual channel allocation and sensor compatibility using the applicable GE Mark VI documentation.

Q: What electrical requirements should be checked before connecting vibration sensors?

A: Verify the 24 VDC board supply requirement, sensor output range, grounding, cable shielding, and any required IEPE excitation. Confirm that the connected sensors match the supported input interface.

Q: Can the IS200TVIBH2B be substituted directly with another Mark VI terminal board?

A: Do not assume direct interchangeability based on series membership alone. Check the replacement board's pin assignments, terminal layout, supported sensor types, and system configuration before substitution.

Field Installation Guidelines

1. Verify board identification: Confirm the complete IS200TVIBH2B model number and inspect the board for physical damage before installation.
2. Isolate power: Follow the site's approved isolation and lockout procedures before removing or connecting terminal wiring.
3. Check sensor compatibility: Confirm probe type, signal range, frequency requirements, and excitation needs against the system documentation.
4. Route field wiring: Keep low-level vibration signal cables separated from high-current conductors and switching circuits where practicable.
5. Apply shielding and grounding: Follow the GE installation documentation for cable shield termination and grounding. Avoid creating unintended ground loops.
6. Inspect terminal connections: Verify conductor identification, polarity where applicable, and terminal tightness before energizing the system.
7. Validate signals: After installation, compare measured input signals with the sensor specifications and configured monitoring channels.
8. Confirm system operation: Check diagnostic indications and control-system channel assignments before returning the equipment to service.

Other Attributes

• Series: GE Multilin 350 Feeder
• Country of Origin: USA
• Lead Time: In Stock, 2 Working Days

In Stock Hot Items of The GE General Electric Mark VI 

Our Competitive Brands

• - ABB Advant-800xA，Advant OCS，Bailey Infi 90 and Net 90，H&B Freelance 2000，DSQC Robots，IGCT / IGBT
• - GE General Electric Field Control, Genius I/O, QuickPanel, RX3i PacSystem, Series 90, Series 90, Series VersaMax
• - Allen Bradley Allen-Bradley SLC500, MicroLogix, CompactLogix, ControlLogix, PLC-5, Panel View,
• - Bently Nevada 3300 System, 3500 System
• - Honeywell 7800 Series, FSC, IPC, Mxopen, TDC 2000, TDC 3000, Experion PKS(C200,C300)
• - Yokogawa Centum CS - Centum VP, Centum XL - micro XL, FA-M3, ProSafe-PLC
• - Ovation, Foxboro, EPRO, Emerson DeltaV, Fuji, Siemens, HIMA, Prosoft, Invensys Triconex, ICS TRIPLEX, Woodward, Bachmann, Schneider

 TEL: +86 18030205725     E-MAIL: manskiwong@cambia.cn

Question 1: Is Our Price Competitive?

NEW-GEN collaborates with over 50 countries worldwide. As a leading supplier in China, we can provide significant discounts to customers based on market demand.

Question 2: What Is The Warranty Period?

We offer a standard one-year warranty for all new and original items.

Question 3: What Payment Methods Do We Accept?

We accept 100% T/T (Telegraphic Transfer) before shipping. For items with a lead time, a 30% deposit is required in advance, with the remaining 70% balance due before shipping. If you have an agent in China, please contact us for RMB transfer.

Question 4: What Shipping Methods Do We Use?

We primarily utilize carriers such as FedEx, DHL, UPS, BRE, etc. If you have an account with any of these carriers, you can arrange the shipping yourself. Additionally, we offer free shipping to China freight forwarders.

Question 5: What Is Our Delivery Time?

Typically, delivery takes around 1-3 days after receiving the advance payment. For items with a quoted lead time, delivery will occur as per the specified lead time.

Question 6: How Do We Package The Goods?

Our packaging process involves multiple layers of protection. Initially, the product is placed in its original box, sealed with a label. Then, we add a layer of bubble wrap to safeguard against collisions during transportation. Finally, all products are securely packed in sturdy boxes for further protection.

Question 7: How Can Customers Contact Us And Request A Quote?

Customers can inquire via email, WhatsApp, WeChat, Skype, or any preferred communication platform. Simply reach out to us, and we'll promptly provide a quote tailored to your needs.